General Information

ACICO blocks are suitable for load bearing and non-load bearing walls. ACICO blocks are delivered ready for use and packed in easily transportable wooden pallets. The pallet should be unloaded at the site by a construction-site crane, forklift truck or other suitable hoisting equipment. Never dump them from the truck.
ACICO blocks are produced to extremely narrow dimensional tolerances of ± 1mm. They are therefore laid by the thin-bed mortar (glue) method. The joint is 1-2 mm thick. ACICO blocks for infill masonry are the logical advancement in development of the tried and proven, conventional masonry technique. Laying by the thin-bed mortar method results in a particularly high quality wall-structure with uniform thermal insulation, without heat bridges in the joints and especially with plane wall surfaces. A further considerable advantage is the fast completion of buildings (structure) with short working times.
ACICO blocks with tongue and groove are recommended for rational straight-course laying, applying thin-bed mortar (glue) to the horizontal course joint and without mortar in vertical one.
ACICO blocks are produced to extremely narrow dimensional tolerances of ± 1mm. They are therefore laid by the thin-bed mortar (glue) method. The joint is 1-2 mm thick. ACICO blocks for infill masonry are the logical advancement in development of the tried and proven, conventional masonry technique. Laying by the thin-bed mortar method results in a particularly high quality wall-structure with uniform thermal insulation, without heat bridges in the joints and especially with plane wall surfaces. A further considerable advantage is the fast completion of buildings (structure) with short working times.
ACICO blocks with tongue and groove are recommended for rational straight-course laying, applying thin-bed mortar (glue) to the horizontal course joint and without mortar in vertical one.
Dimensional Data

Notes:
1. Delivery on wooden pallets (pallets owned by ACICO).
2. Other dimensions can also be manufactured.
3. These formats are in stock in the strength category G2/05
1. Delivery on wooden pallets (pallets owned by ACICO).
2. Other dimensions can also be manufactured.
3. These formats are in stock in the strength category G2/05
Product Characteristic Data

Standard material in stock is
G2/05
1Kn =100 kg
DIN 4165
G2/05
1Kn =100 kg
DIN 4165
Block Laying
How it Works
First dust and loose particles must be brushed from the horizontal joint surfaces. Then apply thin-bed mortar to the horizontal surfaces with a suitbale ACICO plane-block trowel of width equal to block width.
While adjusting the mortar consistency, make sure that during application the thin-bed mortar flows easily through the teeth of the plane-block trowel over the full surface. The consistency should be such that the mortar strands visible on the horizontal joints after applying mortar by trowel cannot mingle. That means the teeth should remain visible.
Bond dimensions must be adhered to. The vertical joint of the lower course must be staggered at least 10 cm relative to the vertical joint of the overlaying course. Now use the rubber hammer to align accurately edge to edge and tap firmly into place.
A few blocks should be removed randomly immediately after laying to check whether mortar is spread over the full surface or not. In summer season, it is recommended to wet the block before applying the glue.
Differences of heights in a course can be adjusted by using plane board. If these differences are not more than 2-3 mm adjusting by thin bed mortar is also possible. All follow-up work on walls of ACICO blocks is carried out in the usual way
While adjusting the mortar consistency, make sure that during application the thin-bed mortar flows easily through the teeth of the plane-block trowel over the full surface. The consistency should be such that the mortar strands visible on the horizontal joints after applying mortar by trowel cannot mingle. That means the teeth should remain visible.
Bond dimensions must be adhered to. The vertical joint of the lower course must be staggered at least 10 cm relative to the vertical joint of the overlaying course. Now use the rubber hammer to align accurately edge to edge and tap firmly into place.
A few blocks should be removed randomly immediately after laying to check whether mortar is spread over the full surface or not. In summer season, it is recommended to wet the block before applying the glue.
Differences of heights in a course can be adjusted by using plane board. If these differences are not more than 2-3 mm adjusting by thin bed mortar is also possible. All follow-up work on walls of ACICO blocks is carried out in the usual way